On This Page
How to Start a Chevrolet with a Dead Key Fob
Starting Your Chevrolet
- First, if you are still locked out, click here for help getting inside!
- Second, you can find video help here!
- Finally, if you need another manufacturer, click here.
Chevrolet vehicles uses all three of the key fob styles made by General Motors. There are also way too many back up start variations, but we have them all here. And you can find a whole lot of videos here.
Here’s the deal: Buckle up, find your model, and if your start battery is still good, we’ll get you underway. Note that they are generally presented as sedans, then SUVs then pick ups.
Corvette
The Coupes made by GM will show up early in this list, including the Corvette (C6, C7 and C8 models). So, note immediately that the latches are electronic and if the main 12-volt battery is dead and you’ve closed the door, the lever to the right is your only escape. You will find it below the door on the floor where you would expect to find a trunk release (right). Pull it up and the door will open. There’s another on the passenger side for that door.
The rectangular style key fob is used in most GM vehicles prior to 2014. 
In Corvette models built before 2014 (C6), the pocket is on the left of the inside of the glove box. Place the transmitter in the pocket with the buttons facing the glove box storage area (right). Then, with the vehicle in P (Park) or N (Neutral), press the brake pedal and the Start / Stop ignition button as normal.
In the 2014 (C7) Corvette, the transmitter pocket is moved to the right side of the steering column, as shown to the left. Place the 
transmitter in the pocket with the buttons facing up. Again, with the vehicle in Park or Neutral, press the brake pedal and the Start / Stop ignition button as normal. Find a helpful video here. See below for the C8.
Newer, rounded “flip key” key fob and a rounded fob with a built in or pull away mechanical key, take over from here.
Camaro, later Corvette
Push button or keyless start is introduced to the Camaro in 2016. It also uses the cup holder as a back up slot, but to their credit, Chevrolet made this one simple. Make sure there is nothing, particularly coins, in the rear cup holder, and simply drop the fob into it. The car will recognize the key and a press of the brake pedal and Start / Stop ignition button will have you on your way. Corvettes (C8), 2020 – 2023, use this spot as well. In 2024, the Corvette spot is moved to the front cup holder.
Impala
The Impala uses a back up pocket located in the front of the center console (right). The model is using the flip key thus far through 2018. Drop transmitter into the pocket with the key ring up and the buttons facing out. With the vehicle in Park or Neutral, press the brake pedal and the Start / Stop ignition button as normal.
Look for video help here.
Volt
With the first generation Volt, open the instrument panel 
storage area located above the infotainment screen and remove the rubber mat. Extend the key blade and place the blade into the slot (right).
With the vehicle in Park or Neutral, press the brake pedal and the POWER button on the center stack to start the vehicle.
Starting with model year 2016, the back-up location for the Volt is 
moved to the center console, as shown. The rubber mat at the bottom of the console will need to be removed, and so anything actually in the console.
Bolt
This is also the location used by the new Bolt EV and Bolt EUV, which will be found beneath a pull-out tray.
The pocket for the fob or transmitter is beneath the pad or tray and to the front. It is also roughly the shape of the fob. Place the fob in the pocket and with the vehicle in Park or Neutral, press the brake pedal and the POWER button on the center stack to start the vehicle. We have a video of the process here.
Cruze
The last flip key back-up start option belongs to the Cruze. You must remove the plastic trim piece from the small storage area next to the accessory power outlet near the front of the console. Extend the key blade and insert it into the transmitter slot (right). With the vehicle in Park or Neutral, press the brake pedal and the Start / Stop ignition button as normal.
Check out the video here.
The 2017 Cruze gets the new key and a new back up location, which is the front cup holder, as seen to the right. Sonic, Equinox and Blazer models now use this spot as well.
Simply drop the key fob into the front cup holder, buttons up, and start the car as normal, stepping on the brake and pushing the Start / Stop ignition button.
Blazer EV
The 2024 Blazer Electric Vehicle (EV) is a different animal. Its back up spot is at the bottom of the center console storage area. Drop the key fob on the spot shown (right) with the buttons up.
And it starts differently as well. Once the key fob is in its spot, simply step on the brake. The instrument panel will tell you if you have been successful.
Trax
The Trax, which first saw push button start in 2017, also uses the front cup holder as its back up slot. However, there are three cup holders in the center console area, with the front one being separated from the two behind it. Be sure to use the one in the very front. See the image to right.
Drop the key fob into the front cup holder, buttons up, and start the car as normal, using the Start / Stop button while stepping on the brake pedal.
Check out a videos for all these models here.
Trailblazer
The new Trailblazer model has the back up pocket in front of the center console storage area and behind the the two cup holders on the console (image at right). Drop the key fob into the pocket or depression, The manual states that the buttons should be facing the front, but we don’t believe this is possible given the shape of the pocket. We also believe that it will not likely matter. With the vehicle in Park or Neutral, press the brake pedal and the Start / Stop ignition button as normal.
Tahoe, Suburban
Until 2021, the large SUV’s from GM, including the Tahoe and Suburban, feature a transmitter 
pocket also located in the face of the front of the inside of the center console. However, the pocket points down, as shown to the right. Slide the transmitter into the pocket with the key ring facing out, buttons forward (in the Suburban we had on hand, the engine started with the buttons facing either way). It is a loose fit, so don’t be concerned. With the vehicle in Park or Neutral, press the brake pedal and the Start / Stop ignition button as normal. Check out the video here.
Traverse
In the Chevrolet Traverse, through 2023, the transmitter pocket is at the bottom of the center console storage area, as seen in the image to the right. The outline of the transmitter will be visible to the front of the console. The 2024 Traverse uses the left or driver’s side cup holder, exactly like the Silverado EV below. Once the fob is in place, press the brake pedal and the Start / Stop ignition button as normal to start the vehicle.
Spark
Spark models also have what is called a transmitter pocket in the center console, but no image defining a location is 
shown in the manual. There are three storage spots in the console (see the red arrows), and one of them will be the “pocket” but none of them are actually marked. Drop the transmitter or key fob in the front storage spot first and attempt to start the car normally, with your foot on the brake and pressing the Start / Stop button.
If this does not work, move to the storage spot furthest back and try starting again. If the car again fails to start, try the longer storage spot alongside the emergency brake. If the starting problem is associated with a dead battery in the key fob, one of the three locations will work!
Silverado, Malibu
In the Silverado pick up (note that the electric version is discussed below) and the Malibu sedan, the pocket for the transmitter is located in the face of the rear of the inside of the center console. Silverado gets push button start for the first time in 2019. Slide the transmitter into the pocket with the key ring facing up, and the buttons out (or however it will fit!).
The Silverado’s pocket is larger, as is the center console, which is actually the center seat in the bench seat. With the vehicle in Park or Neutral, press the brake pedal and 
the Start / Stop ignition button as normal. The pocket in 2021 Tahoe and Suburban models with a bench seat is also moved to this location, at the back of the console.
Tahoe, Suburban, later Silverado
If the Silverado, Tahoe or Suburban models have bucket seats, the pocket is found in or near the the two cup holders. In the Silverado, slip the key fob or transmitter into the insert between the cup holders (first image to the right). In the Tahoe or Suburban, as well as the Silverado EV, drop the 
transmitter into the left side cup holder (second image below right).
Once again, with the vehicle in Park or Neutral, press the brake pedal and the Start / Stop ignition button as normal. The Silverado EV starts when the brake pedal is depressed.
And we have a video of the process here.
Note: If you have made an attempt to start the vehicle without success, there may be residual pressure in the brake system and a new warning light may appear (left) or text 
message to Step on the Brake. Press the brake pedal very, very hard when trying to start the vehicle again to be sure that the release switch behind the pedal is engaged. Or wait a few minutes and try again.
… Return to Part I, Getting In
——————————————————————-
Remember that only proper service and repair procedures will ensure the safe and reliable operation of your car. In addition, proper safety procedures and precautions, such as the use of safety goggles, the right tools and the equipment should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.
These posts are for information sharing purposes only, and should not be used in lieu of an OEM service manual or factory authorized service procedure. We are not in the auto repair business nor do we publish automotive service manuals. Nothing we include on these pages and posts has been reviewed, approved or authorized by any vehicle manufacturer.
Technology is always changing and what is current and accurate today may be literally out-of-date and inaccurate tomorrow. And when it comes to the current state of flux in the auto industry, nothing is more true.
The author has 25 years of automotive experience and has assembled the most extensive collection of symbols and warning lights anywhere (over 1,000!) and can help you open and start any keyless start car with a dead key fob battery. BA, St. Joseph’s College, ME: MS, Rensselaer Polytechnic Institute, NY
First a word of caution concerning the Ford GT. Its latches are entirely electronic, the result being that, in the event of a power failure while inside the car, a back up plan is necessary. There is a strap on each pillar alongside each seat, as seen n the image to the right. Pull it to release the door.
In the Taurus, Expedition (before 2018) and Flex the Intelligent Access key slot is to the rear or the side of the console and points up. The key is slipped in vertically or horizontally depending on the slot’s shape, with the buttons facing out, as in the image shown. After inserting the key, use the Start / Stop ignition button and brake pedal to start your vehicle as usual. If it fails to start, turn the fob so that the buttons face back and try again. Once the vehicle is started, the key can be removed from the backup slot, if you wish.
In the updated (2018) Expedition, and (2025) Explorer (with bucket seats — see well below for column shift models) models the back up slot is in the front cup holder (Expedition) and rear cup holder (Explorer). There is a two-piece mat at the bottom, and the front piece needs to be pulled away. It is a loose fit and slips out easily. Drop the key fob into the slot with the buttons facing the back of the vehicle and start it as normal.
In Explorer and Fusion models, the slot is found near the Auxiliary, USB and power ports in the center console, like the one shown. The Intelligent Access key is slipped in with the buttons facing out (in the Explorer we had, the vehicle started with the buttons facing either direction) and the key ring up.
Transit
The new Ranger compact pick up also uses a cup holder, the rear one. Place the key fob in the cup holder making sure that it is centered and is parallel to the brake handle, as can be seen in the image at right. The truck can then be started by stepping on the brake and using the Start / Stop button as normal.
The Edge back up slot is inside the center console, but actually beneath the the front of the console (right). It is difficult to see, but it can be felt as raised tray just the right size for the remote control. Slip the remote onto the tray with the buttons up and press the Start / Stop button while stepping on the brake as normal.
Escape
In the 2018 Escape, the back up slot is found in the front cup holder. The bottom is marked with radiating lines meant to indicate radio waves. Remove anything that may be in the cup holder and set the fob inside, as shown in the image at right. Once it is placed, use the Start /Stop ignition button to start the vehicle while stepping on the brake as normal.
Bronco, Maverick, Transit (2024 and later)
/Stop ignition button to start the vehicle while stepping on the brake as normal.
The EcoSport, introduced in 2018, also uses a location in the front of the center console. Drop the fob into the slot with the key ring up and the buttons facing the back. After inserting the key fob, use the Start / Stop ignition button and brake pedal to start your vehicle as usual. And again, the key fob can be removed from the backup slot once the vehicle is started, if you wish.
Mustang, Fusion, Expedition
In 2024, Ford moved the Mustang back up start slot to the bottom of the center console. Remove the mat covering the bottom — as well as anything stored there — and place the fob in the fob-shaped depression with the buttons facing up.
Mustang Mach E
F-150, Explorer, F-150 Lightning
If the shifter is on the center console through 2016, the slot will be under the rubber mat in front of the shifter. Remove the mat and insert the Intelligent Access key with the buttons facing up.
In 2017, trucks with the shifter on the center console have the back up slot moved to one of the cup holders. Through 2020, the front cup holder is used, but it is moved to the rear cup holder starting in 2021. All Lightning models use the rear cup holder. Remove the mat at the bottom (see image) by pulling the tab and stand the key fob up in the slot, buttons forward. Then press the Start / Stop button while stepping on the brake as normal.
F-250
The compact Focus has five variations alone, with the Escape and C-Max sharing two of them and the Fiesta sharing one. The fifth Focus variation belongs to 2016 models only. All are located on the right side of the steering column near the windshield wiper lever. And see below for Fiesta and Focus models built after 2020 and not sold in North America.
If you see the transmitter symbol, which may have a key or tower in between the radiating lines, and you have a three button Intelligent Access key, slip the key into a small slot beneath the symbol, as shown.
If you have a five button Intelligent Access key, place the key against the transmitter symbol, as shown in the image, and start the vehicle. The vehicle will recognize the key, even if the key’s battery is dead. Use the Start / Stop ignition button and brake pedal to start your vehicle as usual.
If you see a cover, like the one shown above, there are two options. If a small slot or notch is visible, as seen in the image, pry off the cover using the mechanical key and insert the Intelligent Access key, as shown.
If the covering does not have a slot or notch to pry off the cover, which will include Fiesta models, simply hold the Intelligent Access key against the cover, similar to the five-button process shown above and as shown here, and start your vehicle using the Start / Stop ignition button and brake pedal as usual. The vehicle will recognize the key, even if the key’s battery is dead.
In 2016 and going forward, Ford made a change in the Focus. The back-up slot will be found at the bottom of the center console. It will appear as a depression in the floor of the console in roughly the shape of the key fob.
console storage compartment with the buttons facing up.
Fiesta and Focus models built after 2020 feature a small storage area in front of the shift lever on the center console. The area’s rubber mat must be removed, much like the pick up trucks with center console shifters seen earlier. There is even the mark of a key with lines radiating from it to point out the location (top arrow). Place the fob as shown (lower arrow) with the buttons up. Step on the brake and start the car using the Start / Stop ignition button as normal.
Finally, if you happen to have the GT model, the back up location is a storage tray at the front of the center console beneath its rubber mat, like the Fiesta and Focus above. Lift the mat and place the key fob with the buttons up, as shown in the image. Step on the brake and start the car using the Start / Stop ignition button as normal.
The latest models from all three manufacturers — with two exceptions — have a much simplified process. Staring with vehicle updates in the 2013 model year, simply press the Start / Stop ignition button with the Smart Key while depressing the brake to start the vehicle. We originally named this the back up start Method 6. If this does not work in your model, continue on below for a method that will.
The exceptions noted are first, an EV button (far left) in Kia EVs. It is pushed just like the Start / Stop button. The second exception is the 2021 Genesis G80, which is now a Seventh Method. This method has moved to the 2022 GV60 EV as well, and may yet be placed in other models. If the vehicle does not recognize the key fob or Smart Key, slip the Smart Key into the space behind the shifter dial and cup holders and in front of the leather of the console. See the second image to the left. Then, step on the brake and push the Start / Stop ignition button to start the vehicle as normal.
We must also add an Eighth Method, which is digital. In the new GV60, G70, GV70, G80 and G90, a registered smart phone or a pre-registered card key can be placed on the vehicle’s wireless charging pad. It is found in front of the center console storage area (left). Once in place, the vehicle can be started as normal.
The Kia Forte, Sportage, and Sorento and Hyundai Sonata (prior to 2014) use Method 1. Insert the Smart Key in the Smart Key holder, which is a slot inside the center console, then press the Start / Stop ignition button while depressing the brake. To remove the Key, press it, then pull. Check out the video below.
The Kia Magentis also uses a slot in the center console in Method 2. Insert the Key and then press the Start / Stop ignition button while depressing the brake. To remove, press the Smart Key inward past the detent and then pull it outward.
The Hyundai Genesis, built before 2014, uses Method 3, which is a slot located behind a door above the shifter. Insert the Key and then press the Start / Stop ignition button while depressing the brake. To remove the Key, press it and then pull it out.
The Kia Optima (prior to 2014) and Soul and Hyundai Equus use Method 4, which is a slot in the glove box. The slot is a little higher in the Equus. Insert the Key and then press the Start / Stop ignition button while depressing the brake. To remove the Key, press it and then pull it out.
The Kia Borrego uses the Method 5 slot, which is in the dash just below the Start /Stop ignition button. It should be readily visible. Insert the Smart Key and then press the Start / Stop button while depressing the brake. To remove the Key, release it by pressing and then pull it out.
‘clickers), each of which holds a mechanical key. The rectangular shape Style 1 has a release catch (1) on the mechanical key (2) itself, very near the key ring hole, as shown. Slide the catch towards the hole while pulling on the key to remove it from the Access Key.
The Style 2 Access Key has an oval shape. The release for the mechanical key (2) is a simple push-button (1) on the back of the Access Key, as shown (for the record, it looks like it will slide — it won’t). Pull out the mechanical key while pressing the release button at the same time.
which is also a more rectangular shape. Here, the mechanical key release (1) is on the side of the Access Key, as shown. Pull out the mechanical key (2) while pressing the release button at the same time.
buttons facing out towards you, as shown. The vehicle and the Access Key will talk to each other for a few moments, after which a chime or ‘ding’ will be heard.
To retrieve the mechanical key from either key fob style, slide the release lever located on the reverse side of the FAST key fob, as shown, and pull out the mechanical key. It can then be inserted into the lock cylinder at the back of the driver’s door handle and turned to unlock the car. So far so good…
There are three general styles of key fobs in use with Volkswagen and Audi models. With the older style shown to the right, press the chrome button on the back of the key fob (remote control or ‘clicker’) to release the spring-loaded mechanical key, which remains attached to the key fob.
Newer Volkswagen and Audi models use what they called an Advanced Key, shown to the left. The mechanical key is separated 
from the fob (or remote control or ‘clicker’) by pressing the button on the back side of the fob, shown with the arrow, while pulling on the same key ring end.
And yet a fourth key fob from Audi has a chrome button on the back, similar to the unit above, but below the chrome end. push the button and pull on the key ring end to remove the mechanical key. We saw it first in the new 2019 Q8.
For the Karma model, press the button on the reverse of the key fob (remote control or ‘clicker’) and slide the emergency key blade or mechanical key free (right image).
which could make getting to the next step very difficult while an alarm is blaring.
Place the Fisker logo on the back of the fob against the light colored strip in the center of the driver’s door handle roughly where the arrow is pointing (right). It may need to be moved a half inch one way or the other. The handle will detect the key fob and will extend to the open position.